Dripka how to make the same ones. How to wind drip tape with your own hands: step-by-step instructions

As electronic cigarettes develop, users are increasingly trying to improve their models with their own hands. For what?

1. Saving money.
2. Aesthetic pleasure from creativity.
3. Customization “To suit you”.

One of the most common “upgrade” methods is to repair the evaporator, replace the coil (winding) and change the cotton wool (wick). Many stores are full of related materials for all types of repairs, and forums are full of admiring comments from owners of homemade atomizers.

Let's start with a few of the most popular questions that beginner vapers ask.

1. Which wire (material for the spiral) should I choose?
We will make the choice according to the following criteria: diameter and type (nichrome, kanthal).

You need to choose the type of spiral based on where you are going to install it; if it is a tank where a stainless mesh is used as a wick, then strictly choose Kanthal. If we notice a silica cord, super thread or bamboo yarn in the atomizer, then we can use both kanthal and nichrome.

Before winding the spiral, be sure to burn the wire with a torch, because... after burning, the spiral will lose its “springiness” and it will be easier to wind it up.

The differences between wire types are the alloy composition:

Nichrome is the general name for a group of alloys that consist of Nickel and Chrome, depending on the brand, it may contain other metals to improve certain characteristics.

Kanthal is a registered trademark that produces an alloy consisting of iron, chromium and aluminum; other manufacturers call wire made from the same alloy Fechral (FeCrAl).

Both alloys are used as heating elements in all sorts of electrical appliances - irons, hair dryers, electric ovens for firing and drying, and so on, kanthal and nichrome have several different properties. So, the parameters:

Cantal– heats up evenly and has virtually no spring effect during winding.

Nichrome– does not turn black so quickly, is soft, bends easier.

2. How to make the required resistance?

What are we talking about? To ensure that repairs are repairs and not creations atomic bomb, at the output the atomizer must have the required resistance (depending on the type of battery), therefore, when we create a winding, it is important to monitor the resistance indicators. (using a multimeter).

Remember the main principle : the thicker the wire, the less resistance it has. For example, by making five turns of nichrome with a wire with a diameter of 0.10 mm, you will get a spiral with a resistance of 2.2 Ohms, and by making five turns on a wire with a diameter of 0.20 mm, you will get 1.2 Ohms.

Ready means that you have in your hand a piece of wire with five (or more) turns, having two poles (ends of the wire). They need to be installed (depending on the design of the evaporator housing) so that they are isolated from each other and held tightly in position.

Next we install the wick. It can be made from different materials, including surgical cotton wool. Before installing the wick, wash and dry your hands thoroughly. Roll up the material for the wick and carefully thread it into the spiral turns using turning movements. The wick should fit tightly in the spiral.

READY! Before first use, be sure to “drip” the wick with liquid.

IMPORTANT TO KNOW! Follow the rules for compatibility of battery power with evaporator resistance. If you have a “varivolt” that can accelerate to 6V, the optimal resistance of the spiral for this voltage should be from 3 to 3.5 Ohms. For homemade atomizers, we recommend purchasing batteries with the Variwatt function, since your device will automatically select the required voltage for the evaporator. Below is a table of compatibility and optimal operation of evaporators with batteries (resistance - power).

We hope this article will help you understand the structure of an electronic cigarette. Take care of your health!

Fans of vaping—smoking electronic cigarettes—appreciate the intensity of vapor production. A do-it-yourself drip tip designed for a certain power allows you to satisfy the individual taste of the smoker and create a unique device. You can remake an old atomizer by winding a new spiral, or create a new heating unit from scrap material. At the same time, this will save money: the wire for the spiral costs several times less than ready-made wound heating elements.

Conversion and repair of old drip

Atomizer repair begins with removing the old coil and cleaning the body and stands from soot and dirt. Use a screwdriver to unscrew the screws and remove the burnt parts. The remaining nodes are wiped with a damp cloth.

Making a spiral

Kanthal and nichrome are used for spirals more often than other materials. These types of wire can be purchased at the store; they are easy to wind and can withstand high temperatures.

Before coiling, the wire must be calcined over a fire: after this procedure it will become plastic and pliable.

The internal diameter of the spiral should be within 2.5–3 mm, as in the photo. For winding, you can take a drill with cylindrical shank and wrap the wire around the smooth part. Suitable from scrap materials knitting needle and a nail.

Some rules should be followed:

• both spirals must be identical;
• adjustment should begin with 5 turns;
• Even sections of wire should be directed in one direction and not touch each other.

The excess ends are cut off after the final installation of the spiral into the drip.

Adjustment

The ends of the new spirals are inserted into the sockets and clamped with screws. After this, the degree of incandescence is checked.

The optimal glow for vaping is dark yellow and evenly distributed. If the last turns are darker, you need to tighten the screws.

If you have a multimeter at home, you can use it to adjust the resistance.

The intensity of evaporation is regulated by the number of turns. If the spiral is red, it needs to be shortened by one turn. The brighter the wire glows, the faster it will burn out. The body of the cigarette and the mouthpiece will become very hot and burn your lips. When the wire is heated in a drip tip until it turns light yellow and white 1-2 turns should be added.

Atomizer assembly

After adjustment, the drip tip is assembled and refilled:

1. 1. The free ends of the wire are cut off.
2. 2. Cotton wool twisted into a bundle is inserted inside. It should fit tightly into the spiral and touch it only inside the turns.
3. 3. The wick is soaked in liquid.
4. 4. When blowing from the side, the wick is placed opposite the holes.

The degree of evaporation of the liquid depends on the distance between the turns of the wire: the smaller it is, the weaker the steam is released.

Creating an evaporator from improvised materials

Any vaper can assemble an electronic cigarette from scrap materials. Electrical diagram Connecting to the battery and button is quite simple. Most of the time is spent creating the drip. To make it, you can use ready-made drawings with calculations.

Some parts do not need to be machined, but use plumbing fittings suitable sizes: locknut, nipple and coupling.

Vaping is already a subculture that is attracting more and more smokers. Sooner or later, any vaper will learn about the ability to wind coils onto an atomizer themselves. But doubts always arise whether this is necessary and whether it would be easier to buy a ready-made device. On at the moment there is no need to carry out this process. But still, anyone who winds the spirals themselves will receive a number of advantages.

The first thing you will need is an atomizer that has a base for winding coils. You need to carefully decide on the types of databases. They differ from each other in the form of the presence of a tank. Different models do not use the same view. One of the most popular models is the Subtank. Many people prefer to start with it.

Winding the drip yourself has a number of advantages and disadvantages. And it’s worth starting with the positives.

Saving money

Ready-made windings will cost much more than winding yourself. A head for a tank can cost a couple of hundred rubles. With the same money you can buy up to ten meters of kanthal. One spiral requires up to six centimeters of wire. Thus, you can see how significant the difference is.

Materials you know

You always know what material you are using. Different wires have different characteristics. They have to be sorted out and learned by everyone.

Getting the desired steam

When choosing a replacement “head”, the user loses the right to a large choice. This applies to wire thickness, evaporation areas, and the like. There are a lot of characteristics for a spiral, all of them are important. By doing it yourself, you have the opportunity to achieve good results. This way you can achieve the amount of steam that suits you.

Selecting parts that are not on sale

You always want to try different things. So to speak, experiment. Not all desired parts are sold in the store. For example, it is not always possible to find flattened claptons.

A large number of instructions

How to wind a drip tip? You will never have such a question. It will be before your eyes ready-made example. Information about this is available on forums, video hosting sites, and so on.

Flaws

Cons exist everywhere. Pay attention to them.

Practice and time

It will take a lot of practice to achieve a good result. You won't be able to wind it perfectly the first time. An experienced person spends no more than ten minutes on this. But if you are a beginner, then you may need more time. Replacing other parts - this process can take up to several hours.

Lack of basic knowledge

Not knowing basic things can lead to problems. At a minimum, you will need to know Ohm's law.

Also, if you are careless, there is a high probability of injury. Follow safety precautions.

Materials

There are two most necessary things that a vaper needs besides an atomizer. Wire will serve as an excellent spiral. Cotton wool, in turn, is perfect as a filter. All this taken together will produce the steam you need.

Spiral material

There are several types of materials for spirals.

You should read them carefully:

• Nichrome– low price and excellent delivery options. Comfort is also provided.
• Fechral- the most famous and popular. Similar to the previous one. Characterized by the absence of nickel. For this reason, it costs less and lasts less.
• Stainless steel- Very available material, which will last a long time. Due to the fact that it is inconvenient to wind, it is used very rarely. Now heaters with temperature control have begun to appear. It is possible to work in TC mode.
• Nickel- very expensive material. Rarely used. It is practically not used among beginners.
• Titanium– similar to nickel, but does not emit harmful substances. It is difficult to say whether nickel overheats; this is a highly debated issue. But due to the potential danger, most people switch to titanium.

Material for making wick

The choice of materials for the wick must be approached with great responsibility.

The most common materials used:

• Cotton wool is a very cheap and popular item. You just need to put in uncleaned cotton wool. You can buy it in all pharmacies.
• Japanese cotton is very practical, but relatively expensive. For beginners this can be a problem. It has no aftertaste and is in great demand.

Winding resistance

Resistance is the basis for winding. This indicator depends on the length, thickness and material.

A very common question is how to wind a drip. This will require knowledge of Ohm's laws. Using the battery incorrectly can cause problems. In addition to power, you also need to consider resistance. If winding is incorrect, a mod may be needed. But it is not on sale everywhere. To avoid overheating, batteries are used at high frequency.

Achieving low resistance is very difficult. Various sources will help you with this.

Types of winding

Coils for drippers– it is these details that play a role in the type of winding. Here are the most basic of them:

Nanocoil- a small spiral, the turns of which are located at a short distance. If the situation is successful and there is no short circuit, you can create a large heating area. In this regard, the pair will be larger.

Regular coil– characterized by a large amount of space. There is a lot of space between the turns. Thus, the liquid passes through the filter better. In this case, the pair will be slightly smaller.

Coil braid– a coil, which is made from two windings. This is more of a subtype of spiral. Two wires are intertwined in its center. The flavor and vapor become more intense, but there is a risk of inhaling the liquid. Not suitable for all clears. There are also different sizes.

The electronic cigarette has gained its popularity due to its convenient use. It is believed that vaping is less harmful to health than smoking a regular cigarette. An alternative to a clearomizer in this device drip sticks out. It does not have a separate container for placing liquid, which ensures that it gets directly onto the wick. Thanks to the wide mouthpiece, it is convenient to pour liquid into the drip tip.

How to decide on a drip tip for an electronic cigarette?

Electronic cigarettes come in a wide variety. Modern drips have a number of features that need to be taken into account:

1. Number of racks. The number of spirals depends on this parameter. The number of racks affects the amount of steam. But there is also a drawback. If there are many compartments, the case will heat up more.

1. Airflow. How much a smoker can vape depends on the activity of the stream. It also affects the perception of taste. If the drip device has little resistance to the coils, then they need more airflow.

1. Baths. There is no need to frequently bury the wick. Provided long period smoking. If the liquid is not completely evaporated, it may leak out in a horizontal position.

1. Pin. This element provides throughput, which affects the performance of the electronic cigarette. Best material- silver.

Dripper components

The vape does not stink of nicotine, but on the contrary, it emits a pleasant aroma, usually fruity. The main difference between the drip device is the absence of a special reservoir for filling with liquid. Such advantages suggest how to make a drip yourself. Main components of the device:

1. Chompcap. Acts as a mouthpiece.
2. Frame(side skirt).
3. Base drains. Must have minus and plus stands. Spirals responsible for evaporation are attached to them.
4. Connector. The element secures the device with the battery pack.

DIY dripka

Many vapers in lately began to come up with options for improving their devices.
How is drip made and what should you pay more attention to? Many stores provide a wide range of suitable materials.

• Spiral. The right choice.

The choice of coil type is based on where it will be installed. If a mesh made of stainless material is used for the wick, then it is imperative to use Kanthal. If the device has silica lace, bamboo yarn or super thread, then it is possible to choose kanthal or nichrome.

Before winding the spiral, you should turn to the torch and use it to burn the wire. This method will lead to a loss of springiness and the wire will be much easier to wind.

Wires are divided into different types, the main difference of which is the composition of the alloy. The components of nichrome are nickel and chromium. Kanthal consists of aluminum alloy, chromium, iron. The main purpose of both alloys is to provide the heating capacity of the elements.

• Resistance. We calculate correctly.

The electronic cigarette will be made with high quality and safety, thanks to the provision of the necessary resistance. Using a multimeter, it is easy to monitor the readings.

The resistance depends on the thickness of the wire used. The thicker it is, the less resistance there will be. For example, if five turns are made with a 0.10 mm wire, then the spiral will be provided with a resistance of 2.2 Ohms. If you make five turns of 0.20mm wire, you get a resistance of 1.2 ohms.

• Wick.

When the spiral is ready, you can begin installing the wick. You should end up with a wire (five turns, more if possible) with two poles (wire ends). Both of these ends must be insulated and securely fixed in the specified position. This point will depend on the characteristics of the case itself.

Now you can begin making the wick and installing it. The materials can be any; generally, specialized cotton wool is chosen. When working, hands must be completely dry. Slowly thread the selected material through the spiral turns using turning movements. The main thing is that the wick is firmly fixed in the spiral. The last rule is that the wick must be dipped in liquid before using the device for the first time! Such simple instructions can bring a lot of pleasure as a result.

For homemade device It’s better to buy a battery with a Variwatt function. Then the required voltage for the evaporator will be selected automatically.