Homemade equipment for car service. Useful DIY garage gadgets

Absolutely anyone can make accessories for their garage with their own hands. With the help of such products, the owner of the premises will free up a lot of space, and tools and equipment will always be at hand.

A workbench is a necessary product in every garage

A homemade workbench should be in every garage. It does not take up much space and makes it possible to comfortably carry out repairs and manufacture useful crafts. Typically a workbench is made from strong wooden planks that are attached to a thick wooden beam or profiled pipe. Often workplace made from steel billets. They are quite easy to cut and fasten into one durable structure using metal corners and universal self-tapping screws.

To make a workbench, as well as other machines for the garage, you need to draw an accurate design plan. At the same time, take into account the space that will be allocated for the product. It is best to place the structure next to shelves or racks. In the drawing, indicate the presence drawers and shelves. You will store small fasteners and tools in them. You can also attach a compact vise to the tabletop. Having drawn up a plan, start making the workbench. First, we assemble the tabletop.

If you have small room, then there is no point in making a large homemade product for it. You can connect the boards together using good glue and metal ties. As a rule, the tabletop of a standard workbench consists of 5–10 identical boards. Next, we make special grooves measuring 2.5x2.5 cm on the tabletop. They are needed for stops. As soon as the glue on the product has dried, the surface must be planed. The result should be a perfectly smooth coating. The legs for the structure can be made from several bars measuring 80x10x10 cm.

We make grooves in the front legs into which the brackets will be inserted. In the future, the latter will be connected to the longitudinal beam of the tabletop. Then we assemble the base of the underframe. It consists of two frames, which are made from 5x10 cm boards. The base is attached to the support, after which the frames are cut into the legs of the workbench by 2.5 cm. At the end, we secure the components with bolts. Then you need to attach the back and side support walls to the workbench. To make them they take chipboard sheets or centimeter plywood.

The last step will be connecting the tabletop and the upper frame. To do this, you should use powerful bolts. Afterwards we apply drying oil to the surface of the workbench. As soon as it dries, we treat the surface with varnish. As a result of the work, you received a stable structure on which you can not only repair spare parts or make various crafts, but also store tools.

Making a rack - about a complex design in simple words

Every driver probably has a lot of large garage equipment that there is no place to store. Where can you find such a place for them so that later you can quickly find the right tool? The correct answer is on the rack. This design will allow you to organize free space and save a lot of time. Similar devices for the garage can be made of wood or metal. The second option is more reliable, but it is quite difficult to implement it yourself.

The first one is much easier to complete, however, in order for the structure to last for a long time, it is worth choosing strong wood species for the work. Beech or oak are perfect for this. Boxes and shelves made from them can withstand significant loads. In principle, the norm for a rack is the ability to withstand a weight of 150–180 kg. In practice, only a few adhere to these recommendations. However, it is definitely worth remembering that the maximum weight of all tools on the rack should not exceed 300 kg. Otherwise, this design will become dangerous for the garage owner himself.

Making a rack that is complex in design is very difficult. It requires significant effort, a lot of time and equipment. It is not much inferior to a simplified product, the manufacturing algorithm of which we will consider in more detail. So, the operating procedure is as follows:

1. First you need to take a board 9 cm wide and cut it into pieces of different sizes. In the future, these parts will play the role of supports for the structure.
2. For shelves you will need to take a thicker board. It must be cut into several identical parts.
3. Next, take a board for the base of the rack and mark on it the points at which we will make spacers. They should be located at a distance of 3 cm from the edges of the base.
4. Attach the upper spacer using superglue. We nail the top shelf to it. The same manipulations must be repeated with other spacers and shelves. The bottom expansion part should be attached last.
5. Then you need to turn the assembled product over, tighten the base of the rack with spacers, using screws for this.

After the work done, your rack is almost ready. At the end, all you have to do is clean the surface of the rack with sandpaper and treat it with oil varnish. It is best to apply the latter in 2 layers. Attach the structure to the wall with powerful anchor bolts, screwing in fasteners under the upper and lower shelves of the structure.

Cyclonic vacuum cleaner and press - useful homemade products for those who like to tinker

The list of homemade machines and devices must include a press. This clamping device will become an indispensable assistant for every DIY enthusiast. To make a press you will need hydraulic jack, metal platform bed and 4 profile pipes. Two of them should have a cross-section of 4x4 cm, and the rest - 6x6 cm. To make a press, we take two pipes with a smaller cross-section and attach them to the base of the product. At the very top, between these pipes, we weld another pipe with a larger cross-section.

Install the remaining pipe so that it can easily move along the previously installed guides. The device made in this way works very well. simple principle. To connect two products, they need to be placed on the base of the press and covered with a thick plywood sheet. The pipe with the jack installed must be lowered, and then the two short pipes must be turned. By making this simple movement, you will securely connect the two previously supplied products.

Second device - cyclone vacuum cleaner, it will help you always keep your garage in perfect cleanliness. To make it, prepare a plastic or metal container. Important nuance– the lid of the vessel must be tightly closed. Next, we make 2 small holes in the lid. The first should be located in the center, and the second should be located near the edge. The hole diameters and cross-sections of the hoses you use must be the same. We connect the pipes to the holes. The first will serve to collect garbage, and with the help of the second you will connect a regular vacuum cleaner

Install a plastic elbow into the inlet pipe. With its help, air will be sucked into the device, like a cyclone. Thanks to the presence of this elbow, the vacuum cleaner will be able to suck in not only dust, but also small stones, sawdust, lumps of dirt and other small debris. All this will remain in the container to which you connected the hoses. If you wish, you can not equip the vacuum cleaner with a knee. But in this case, you will not be able to remove garbage, only dust. In such a device it is most advisable to use plastic container and narrow hoses. If you need a more powerful device, then you should make a vacuum cleaner from large hoses, an elbow and a steel container.

Device for making ropes - ropes from plastic bottles

When heated, plastic bottles shrink quickly. Thanks to this, we are able to make fairly strong ropes from them. With their help, the garage owner will be able to connect several various products which are used on the farm. To create the device, you need to find two bolts with nuts and washers, a piece of thin board, an electric drill and a utility knife. After that, take two washers and place them in the middle of the board. The centers of the washers should be marked on the board with a marker. We drill holes at the resulting points.

Next, drill holes on the back of the board. This must be done to prevent rotation during operation of the device. The next step is to screw in the bolts. We are testing the device. We put several washers on the protruding ends of the bolts. The final thickness of the rope will depend on the number of bolts. Next, place a stationery knife or a small piece of it on top of the washers. We secure the device with additional washers screwed in until it stops. Next, the device must be fixed on the desktop using clamps.

Then we take a two-liter plastic bottle, cut off its bottom and cut a strip in the remaining part. We place the latter on the device so that it is located under the knife. Next, we take the strip with one hand and pull it, while holding the plastic container with the other hand. As a result, from one unnecessary 2-liter bottle you will get about 20 linear meters ropes.

How to make a viewing hole - detailed instructions for beginners

Whatever one may say, sooner or later the car has to be repaired. And so that the car owner does not have to crawl under the car and “squirm”, bending double, it is necessary to dig a hole in the garage floor for inspection and repair. First of all, those who want to do this must mark the area of the room where the car is parked. To do this, the area of the garage is marked with chalk. When creating markup, there are several important factors to consider. The length of the pit must correspond to the length of the car, and another 1 meter must be added to this value. The width should be such that it is convenient for you to work. However, be careful - this value should not be greater than the distance between the wheels of the car.

The depth of the hole is calculated taking into account the height of the garage owner. Another 20 cm is added to this indicator.

“Having taken measurements”, start digging a hole. Once you've done this, think about the arrangement inside. First of all, this concerns the walls of the pit. For this purpose, brick, building blocks or concrete can be laid on the sides. The thickness of the walls directly depends on the material. So, if you use ceramic bricks, then this figure should be 20 cm. If you purchased cement, then the wall thickness should be 12 cm. If you want to make walls from blocks, then their thickness should not exceed 22 cm.

Do not forget that the walls of the pit will require hydrophobic impregnation. It will protect materials from moisture. Impregnation must be applied with inside bricks or blocks. To make entry and exit more comfortable, we make steps in the front part of the pit. It is best to use cement for this. You need to start from the lowest step, gradually rising higher. Each of the staircase elements must be the same. To achieve this, first measure the height of the rise and calculate the number of steps.

Shelves in the room - for storing loose fasteners and more

Sometimes the garage space does not allow you to make and install a large, spacious shelving unit. In this case, you can make shelves different sizes. They will be attached directly to the walls at any height convenient for you. This will make it possible to save space on the floor of the room. First of all, you will need to determine where the shelves will be fixed. On the selected section of the wall we make approximate markings, dividing the area into equal squares. Dowels will be screwed into the corners of these squares to hold the shelves.

To screw in the fasteners, drill holes for them using a hammer drill. If possible, it is worth purchasing special dowels with hooks at the ends - they will provide better fixation of the products. Next, we take a thin board and attach hangers with eyes to it. When calculating the distance, be guided by the markings you made on the wall surface. To secure metal hangers, use reliable self-tapping screws. After that, all that remains is to make the shelves. We take several boards and cut them into equal parts - they will serve as bottoms for the products. Then we cut out the walls of the shelves from thicker boards. We nail or glue them to the bottoms. If desired, the products can be painted or varnished.

The final stage will be the installation of finished shelves in the designated places. When installing each of them, carefully ensure that the products stand level and move freely along the guides. If you want, you can glue machined pieces to the front walls of the drawers. wooden handles. It will be more convenient to use the shelves with them. Very interesting idea will be making shelves from plastic canisters.

If you have a sufficient number of these containers, and in the future you do not plan to use them for their intended purpose, then you can use them according to this principle. First, we cut holes in the outer walls of the canisters. At the same time, make sure that only the right or only the left wall of each container is cut off. Otherwise, the shelves will look inorganic. After cutting out the outer walls, clean the plastic from burrs. To do this, use a file. After this, all that remains is to install the shelves in place in the wall or use them as drawers in the shelving unit.

A garage is more than just a place to park a car. It is also a workshop, a place of relaxation, and a club of interests. Therefore, the arrangement of the garage should be convenient and thoughtful. You need to place a lot of things in a small area, and they should be convenient to use. Homemade products for the garage will help with this. What people don’t do with their own hands. From a simple shelf to a complex device. You can make all this yourself. But you need to know how. Several ideas for modernizing a garage and a plan for their implementation are in the article.

Homemade garage: ideas for arrangement

Setting up a garage is a long process. You won’t be able to do everything right away. You have to constantly modernize, change, and create something new. In this case, they mainly use homemade products for the garage. It requires less money and it’s also fun - making something out of garbage the right thing- it's worth a lot.

Tire and wheel storage

Every car owner is faced with the problem of storing out-of-season “shoes” for the car. Where to put the tires is a sore point. In general, the way tires are stored depends on whether they are mounted on rims or not.

So tires with rims can be hung or stored lying down - in the form of a stack, stacking them one on top of the other. To hang tires, you can use luggage straps, chains, or a metal cable with a diameter of 4 mm or more in a polyethylene sheath. Fasten the belts to the ceiling, wall, or beam located above.

Another affordable way- drive pins or hooks with a small bend radius into the wall. The distance between the hooks is slightly larger than the diameter of the tires. The length of the pins should be such that they do not protrude beyond the tire. You can fill them almost to the ceiling so that the wheels fit.

Tires without rims can only be stored standing up. Special shelves are made for them. They are usually welded from profiled pipes. 20*20 mm, maximum 30*30 mm. You can also use a corner. Round pipe It’s inconvenient to cook, but cross members can be made from it - the tires fit and hold up better in this case.

The width of the shelf is 4 times the width of the tire, plus a margin of 10-15 cm for some freedom. The height of the rear wall is slightly higher than the outer diameter of the wheel. The design is simple = from the side it resembles a right triangle. Having it, welding such a shelf will not be difficult.

A shelf for storing tires is an excellent homemade product for the garage. This is a factory option with a completely inhumane price tag. But you can borrow an idea - the crossbars can be rearranged depending on the size of the tires...you never know A shelf for tires in the garage with limited space. No tires - you can fold the shelf

Such shelves are usually hung on the wall. But the place must be chosen so that light does not fall on the rubber - this will deteriorate it. Not the most complicated DIY projects for the garage, but very useful.

Workplace

Probably the largest number of homemade projects for the garage is related to the equipment of the workplace and tool storage systems. Moreover, this is not the only way to solve this problem. First of all, you need to decide where the workplace will be located. There are three options:

The entire width of the far wall. If the garage is of sufficient length and it is possible to “steal” about 1.5 meters. The advantage is that everything is located compactly, at hand, and does not interfere with walking along the car. The disadvantage of this solution is that you have to carry tools far away if work is carried out outdoors.
Tabletop and many drawers. The main thing is to remember where everything is
Along one of long walls. This arrangement is chosen if the garage is wide but not long enough. It makes sense to place the table and workbench to the left of the entrance - on the driver’s side. But this is not critical. The disadvantage of this arrangement of the workplace in the garage is that you have to move with some caution, but it is more convenient to bring/take out tools outside.
The main thing is to place the tools correctly
Occupying one of the corners. This is an intermediate option. Moreover, one of the sides can be made longer, the other shorter.
Placing a desktop in the corner of the garage and placing a sofa next to it is not a solution to the problem. Occupying two adjacent sides is a great idea.

A table or workbench for a garage is made of boards and covered with plywood. Inexpensive, quite reliable. If you have a welding machine and checking skills, you can weld a frame from a corner or profiled pipe. Again, it is better to sheathe it with moisture-resistant plywood. The result is a smooth, abrasion-resistant surface. You can, of course, use it, but the laminating layer is quickly damaged.

To prevent the space from wandering around, you can install shelves or make drawers under the countertop. Boxes are more convenient, but making them is still a hassle. It is quite possible to make shelves and put boxes made of plywood on them. Plastic boxes and baskets are also suitable. But the walls must be thick.

There is, by the way useful idea— make a rack for storing tools from used canisters. Find ones that have the handle on top. Then everything is simple - one of the sides is cut out and in the future this canister is used as a box.

It’s not necessary to make a whole rack - it’s still difficult to remember where and what is located. But you can use the same principle to make drawers for shelves. By the way, you can stick inscriptions or pictures on the ends (with pictures, identification is faster). Such homemade projects for the garage bring satisfaction - create useful thing out of the trash - a pleasant feeling.

Tool storage

The most difficult task is organizing tool storage in the garage. We must make sure that everything is in order, but at the same time, is at hand and in sight. Moreover, closed boxes are suitable only for very organized people who always put the taken item back in its place. Otherwise, you will constantly rummage through drawers, forgetting where everything is. There are several ideas for convenient storage of small items and tools. These are very simple DIY projects for the garage.

An ordinary metal mesh will help to quickly solve the problem. A reinforcing mesh made of 2 mm wire, a 10 cm cage, is suitable. Attach it to the wall, bite off some rods, bend them, make hooks, crossbars, etc. out of them. You can buy special hooks that are attached to the mesh (available in stores that sell commercial equipment); ordinary double-sided hooks, which can be bought or made from wire, are also suitable.

A grid on the wall is a way to quickly organize tool storage

It is convenient to store screwdrivers on a special shelf. Take a board, plywood, 10-15 mm thick. The board must be sanded well so that there are no splinters. Then drill holes of different diameters in one or two rows in the plane. If the board is wide enough, you can make larger holes for chisels or even hammer handles. Clean all the chips again. Now we need to come up with a wall mount. You can use a regular bracket. Screwdrivers, chisels, and other similar materials are inserted into the holes. Convenient, fast, everything is in sight.

There are still useful homemade products for the garage, which allow you to organize storage hand tools. Pliers, pliers, wire cutters, etc. placing it conveniently is problematic. You can hang it on a net. It’s convenient to take off, but not to hang it up. But there is a simple solution - attach a narrow board and put the tool on it. To make it sit comfortably, grind down the board on one side. When cut, it should look like an isosceles triangle.

More simple idea for storing cordless tools, chargers and spare batteries for them. Make a shelf as in the photo above. Cuts of different formats are made in the lower part, and the upper parts are used as regular shelves. The idea is that everything is in one place, quickly taken out/installed in place. These garage DIY projects will make your workspace comfortable. It will be easy to maintain order.

Homemade carriers for the garage

Even with very good lighting in the garage itself or on the street during the day, visibility under the bottom of the car is very low. To illuminate the front of the work, portable lamps are used. These are the simplest DIY projects for the garage. With them you can begin the epic of arranging and equipping your garage space.

In the very simple version This is a socket attached to a wire and can have a small shield with a hook attached to it. This is such a simple thing. The light bulbs used are ordinary ones - incandescent or economy ones with a standard socket. Everything is not bad, except that these light bulbs break very often, you need to figure out how to hang them so that they shine in a specific place. In general, the design needs improvement. There are several modification options.

Unbreakable lamp socket

This lampshade is from plastic bottle perfectly protects the fragile bulb of an energy-saving lamp. You can also use an LED lamp, but an incandescent lamp will not work - it gets too hot. The design is simple - a cord with a plug and a cartridge at the end.

The main task is to find a plastic vessel with walls made of translucent milky plastic of medium thickness. Transparent will not work - it will not scatter light, too thin walls will not save the lamp from impacts. After you have found a suitable vessel, some small change remains:

Everything is simple, but such a lamp allows you to brightly illuminate exactly the desired area, the rest of the space is filled with even light that does not hurt the eyes.

Carrying LED Recessed Light

The simplest and most common homemade products for the garage are portable lamps. Without them, it is inconvenient to work not only in, but even just on a workbench. Need a flat built-in led lamp, which can be switched on at 220 V. These models are called “tablets” because of their shape. You also need a cord with a plug, a piece plastic window sill- to install a lamp. The window sill piece should be larger in size than the lamp. You choose the specific sizes yourself. The next steps are:

That's it, the homemade carrier is ready. This option is for floor installation. The movable leg allows you to change the angle of inclination. To make it turn over less, you can attach a couple of weights inside the body (in its lower part).

Attach the carrying cord to the ceiling

Convenience comes from little things, and very simple homemade products for the garage help with this. For example, you can remove the cable from a portable lamp that always gets tangled under your feet. Carrying is usually done with a cheap cable. It is not the most flexible, does not fold well, and its coils on the floor get under your feet. In general, it is inconvenient to use. You can protect yourself and carry it by hanging the cable from the ceiling. The solution is simple but very effective.

You can make this “suspension” to the ceiling for carrying with your own hands in an hour

Two anchors with a ring at the end.
Cable tie.
Clamp clamp.
Metal cable. The length depends on the size of the garage - it needs to be from one wall to the other.
Steel/plastic rings or steel wire and a piece of pipe to make these rings.
Carrying with a long cable - its length is approximately double the length of the garage.

The cable is stretched along the long side of the garage. It’s more convenient - not far from the “working” wall, where the workbench or other equipment is located. A little work:

In general, everything. You can use it. With such a device, the carrier can be carried to any end of the garage without the cable getting tangled or caught. Convenient, takes little time.

DIY garage compressor

A compressor is needed in any garage. And, by the way, this is not the most difficult homemade product for the garage. A low-power compressor for the garage for inflating tires and other small jobs can be made with your own hands from auxiliary materials. For example, from a compressor from a refrigerator. For this you will need:

refrigerator compressor;
a sealed cylinder with thick walls (you can use a fire extinguisher flask or a small gas cylinder);
safety valve at 8 atm;
pressure gauge;
fitting;
oxygen hoses with couplings (select the length based on the size of your spare parts);
base for the compressor - a thick board or piece of plywood will do.

In order not to pump any nasty stuff into the tires, it is advisable to also install a filter to separate oils, dust and other contaminants. Scheme homemade compressor shown in the photo.

The compressor must have a starting device. We plug it into the network, see which tube the air is sucked into, and mark it. You can put a car filter on it - clean air will be pumped in.

We assemble an oil separator receiver from a cylinder and a safety valve. To do this, we cut two fittings into the cylinder - for air inlet and outlet. We place a safety valve on the inlet hole and connect the compressor outlet to it using an oxygen hose.

We install another automobile oil filter at the outlet of the oil separator receiver to completely remove the oil. We connect the filter to the pressure gauge, and from it comes a hose, which is connected to the tire through the appropriate adapter.

Assembly is complete. But in order to carry this device conveniently, everything needs to be secured in some way. You can weld the frame to size, attach wheels and a handle for easy transportation. One of the compressor options for inflating wheels is described in the video. There is no receiver, but its functions are performed by an oil filter. You can do it this way, but with a receiver the design is more reliable.

Since the compressor in the refrigerator is low-power, it may take a long time to inflate the tires. You can make it more powerful by installing two compressors that will start simultaneously. Accordingly, the pressure will build up twice as fast. But such an installation requires a more robust security group. Such homemade products require a little more equipment, since the circuit is still more complicated.

A garage is not only a place for a car, but also a source of invaluable additional space, which can be used truly rationally if you design useful devices with your own hands.

DIY garage accessories

Since the garage, by its intended purpose, is a home for cars, you should be careful to ensure that the space for tools is well organized. Also in the room there will probably be several square meters in order to remove some of the items from the apartment so as not to clutter the living space.

During installation various devices indoors, it is important to consider that all available equipment is at hand. To do this, you can use the following recommendations:

Rational organization of space in the garage creates many tangible advantages:

it becomes possible to independently carry out short-term repairs of car parts and other mechanisms, due to which you can significantly save money;
Convenient placement of tools significantly speeds up work and saves time;
creating additional places for storing tools, old things, clothes makes it possible to relieve the apartment of things that are rarely used in the household;
finally, the well-thought-out internal logistics of the premises allow it to maintain its attractive appearance and avoid clutter.

PLEASE NOTE. At the project development stage, it is important to take into account the area of the room, and also take into account several mandatory utility compartments - for storing summer and winter tires, cans, jacks, etc.

Video TOP best ideas for decorating a garage with your own hands

Garage rack: step-by-step manufacturing instructions

Since the garage always contains quite a lot of items, organizing their arrangement is a fundamental requirement for proper storage. The simplest and at the same time convenient option- this is the creation of a rack with shelves.

Preparatory stage

Before you begin installing the structure, you should consider several important requirements:

The total weight of the rack should not be more than 4-5 centners - otherwise the structure will be very difficult to move if necessary. It will also put significant pressure on the floor, which can deteriorate the quality of the coating.
When choosing materials, it is important to proceed from considerations of strength and durability of the structure. Metal is optimal, as well as wooden products from beech or oak. Plastic shelves are not suitable - they are not durable and, moreover, may not withstand temperature changes.
Choosing between metal and wooden structure, you should proceed from your specific needs. Metal is more durable and stronger, but wood is more affordable. If you need to place a few tools, it is enough to make a small wooden rack.
Since all the tools are very heavy, you should immediately calculate the strength of the structure so that it can withstand at least 100-150 kg on one shelf.

Installation of a wooden structure

To make such a device for a garage with your own hands, you will need ordinary working tools:

hacksaw for wood and metal;
hammer, nails;
screwdriver, self-tapping screws;
construction tape;
construction level;
electric drill.

Before assembly, it is important to prime and varnish all wooden parts. The garage may experience high humidity or temperature changes - so without treatment the wood will not last long.

Video - Do-it-yourself wooden shelving technology

Installation of a metal structure

Metal structures are exceptionally durable and strong. Moreover, they do not need to be processed special materials to prevent rotting.

You can make both a rack and individual designs, for example, for storing rubber.

In this case, you should take into account the rules for storing tires, which are shown schematically in the figure.

At the design stage of a metal rack, you should take into account that all the necessary items can be freely placed in it. You can take this drawing as a basis.

Or this option.

The easiest option is to purchase a modular design and assemble it yourself. But you can make this device for the garage with your own hands. The sequence of actions is as follows:

It is better to place the heaviest equipment on the lower shelves for optimal load distribution throughout the rack. At the same time, the most best option– when the lower floors are made of corrugated metal, and for the upper floors it is quite acceptable to use durable chipboard.

Hanging shelves: fast and practical

Not in all cases there is a need to create a rack, since it will take up a lot of space. On the other hand, in a garage of any size there is always unused upper space, which can easily be used for hanging shelves.

Structurally, it is quite possible to make any version of such a device for the garage with your own hands:

The tools you will need are the standard set described above. The sequence of actions is as follows:

If the shelf is mounted to the ceiling, you can strengthen its connection to the wall using metal corners - then the product will not swing and will last much longer.

The entire technology is shown schematically in the figure.

Making a shield shelf

The DIY technology for making such a device for a garage has its own differences compared to installing conventional shelves:

The shield itself is made of durable plywood, the parameters of which are selected according to the situation. Visually, the shield should completely cover the surface of the desktop.
Space is allocated on the board for all shelves and appropriate notes are made.
Next, all the holes into which the dowels fit are made in the surface of the structure. It is on them that the hooks will be attached, on which all the tools will be placed.
The shield is secured to the wall using brackets. The corresponding holes are made using a hammer drill.

All steps are shown schematically in the figure.

DIY tool panel above workbench in garage

Workbench for the garage: step-by-step instructions

Another structure that will probably be needed for repair, plumbing and other types of work is a workbench. It can be purchased in a store, but if you have a certain skill, then it is quite possible to make such a device with your own hands and put it in the garage.

Before carrying out the actual installation work It is important to clarify several important details:

Where will the table be located?
What kind of work will mainly be carried out on it.
What work surface material is suitable - metal or wood?

All these questions are closely related to the purpose of the product. If work is expected to be done frequently, then it is better to choose durable metal. And for standard household tasks, durable wood will do.

It is important to understand that a workbench is not just a work surface. Often it combines the function of a wardrobe, a small chest of drawers and even a metal safe - this set of parameters depends on the specific configuration of the product.

Types of workbenches

The key classification of workbenches is based on the types of work that are supposed to be carried out on it:

At the same time, these functions can be combined, so such a classification is largely arbitrary. The best option such a garage device is a design based on metal frame with wooden table top and drawers. It is more reliable than its wooden counterpart, and allows you to save on manufacturing due to the fact that some parts will be made of wood. The table surface can be strengthened metal sheet– then the workbench will last a very long time.

Technology for making a workbench from a metal frame

To install the structure you will need a standard set of tools and materials:

welding machine;
grinder for metal;
building level;
jigsaw for wood;
screwdriver, drill;
self-tapping screws, anchor bolts;
hammer and nails;
metal corners with parameters 5*5 cm;
square pipes 6*4 cm, total length about 24-25 m;
steel strip 4 cm thick, up to 8-9 m long;
paint for wood and metal processing.

These parameters are intended for the manufacture finished product with table parameters 220*75 cm, as shown in the figure.

The sequence of actions is as follows:

Even at the stage of designing a workbench, it is important to decide whether the device will be collapsible or whether it will be permanently installed in the garage. In the case of a collapsible version, all parts are attached using self-tapping screws, and the principles of the technology will be different.

Wooden workbench manufacturing technology

A wooden workbench is less durable than a metal one. It is well suited for cases where the work is supposed to be done less often - several times a year.

To make this device for the garage with your own hands, you can use the same drawing given above, or take the diagram shown in the figure as a sample.

The algorithm will be something like this:

Do-it-yourself garage tipper: step-by-step video instructions

Along with creating the considered devices for the garage, you can also take care to make with your own hands the working tools that will be needed directly for maintenance auto.

One of the most useful installations– a tipper for inspecting the bottom of the machine. The need for such a product is most relevant for Russian realities, since not in every case there is a real possibility of constructing an inspection pit.

Detailed video instructions with step-by-step manufacturing diagram

Before making such an installation, it is extremely important to consider the issue of safety. Even a light car can cause an accident if it falls and, at a minimum, will receive serious damage. Therefore, you can only undertake the creation of such a design if you have sufficient skill.

Making your own garage fixtures allows you to rationally organize interior space and essentially get your own workshop in which you can carry out any ongoing repair work.

Original ideas for organizing space in the garage

And finally, a photo selection of visual ideas for creating spacious structures from a variety of items that are likely to be found in any garage.

A good owner always has his own workshop, which he fills with equipment and devices to suit his needs. Some things can be bought, but others can be built with your own hands. And we must not forget about the garage, because all the necessary equipment should also be there.

It is impossible to provide for everything that might ever be needed. Therefore, we will consider the most basic machines and mechanisms that can be useful when working with wood or metal.

How to make a universal machine with your own hands

There is a huge amount of different types of equipment, many of which can be made independently in one form or another. Craftsmen have even learned to combine several functions in one device.

For example, you can make a universal mechanism from conventional drill which will work like:

circular saw;
grinding;
cutting;
sharpener;
turning.

To make it, you need to attach a drill to the frame. A board with a thickness of 20–25 mm is chosen as the base. The drill is fixed to that part of the body that is intended for attaching another handle.

The location of fixation on the tabletop is selected based on the size of the circular disk, grinding wheel, cutter, or sharpening stone.

To secure the drill, use a firmly fixed threaded rod and nut. Rigidity of fixation is achieved using epoxy glue and, as an addition, a pin 2 mm in diameter. We build a moving sole and that’s it, the base is ready.

To get homemade circular saw, install a saw blade with a diameter of 15 cm on the drill chuck and make a slot for it in the bed. The saw blade must be protected by a metal casing.

If you plan to use a flat cutter instead of a disk, you need to additionally make a rectangular slot or widen the hole for the saw.

From this “circular” saw you can build a cutting mechanism. To do this, on a rigidly fixed surface we install a rotating bracket, a miter box that sets the cutting angle, guides and devices that secure the workpiece.

We combine this with circular saw on the bed. Grinding and turning machines are assembled using the same principle.

Video: homemade circular saw + plane

Making a circular saw with a frame

If you want to have a separate circular saw, then you can easily build it from a manual circular saw bought in a store. Such homemade mechanism not designed for too heavy loads, but suitable for occasional use on the farm.

We take a frame of suitable size and fix it on it manual circular saw, make the maximum cut and leave it in that position. We turn the base over with the circular side down and place it firmly on the frame with legs.

We make a guide and everything is ready to go. Please pay special attention to the height of the machine, you should be comfortable working with it, and its height should be commensurate with your height.

You may also need a pipe bender in the workshop. This is a device that allows you to bend pipes from almost any metal, as well as strips. Bent pipes are required when a person decides to make, for example, a greenhouse or a greenhouse or something like that.

There are different types of pipe benders, let’s say, made independently. There are very simple ones, and there are others that are similar in design to factory ones; they are more difficult to manufacture.

The simplest option homemade pipe bender we get it by sawing the board on one side in a semicircle. Then this workpiece is attached to a stable surface and a limiter is mounted nearby - a wooden part that has space up to the semicircular workpiece, into which one end of the pipe is inserted.

Video: we will equip the workshop ourselves

Features of homemade devices and equipment

You can talk for a long time about what equipment you can make for your workshop with your own hands. But everyone has their own needs and capabilities. Except homemade devices, there should be places to store tools, as well as a workbench.

You should take the construction of a workbench seriously. You need to think about what will be attached to it, where it will stand, and what materials to build it from. The tabletop can be made of metal or wood.

You can immediately attach a circular saw, for example, or a jigsaw, various kinds of vices, clamps, and so on. It all depends on your idea and need for this or that equipment. But the workbench must be the right comfortable height, stable and well made.

Also in the workroom, various types of cabinets and pencil cases for placing and storing existing tools, which you can assemble with your own hands, are very useful. You can equip separate places for storing large tools and separately for small ones, for example, a separate open cabinet for drills.

The convenience of work, how quickly you can find the necessary tool or part and, ultimately, your comfortable well-being depends on how you organize your workspace.

Video: wood lathe

What can be done for the garage

Often, a garage becomes not only a place to store a car, but also a place for many necessary tools, and sometimes a workshop at the same time. Therefore, here you need to have:

Tools for car repair.
Spacious racks for their placement.
Garage workbench.
Hooks.
Shelves or brackets for tires.
Lamps and heaters.

These devices are easy to assemble with my own hands. The organization of the garage space should be well thought out. Everything should be placed conveniently and not take up much space. Think about whether you need a workbench and where to put it, what size it will be and in what places to place racks and shelves.

A workbench will be needed if you are repairing your car yourself. Typically, all tools are located on shelves and racks next to the workbench. Spare tires are stored either on a special rack or hung on brackets on the walls.

Place all fuels and lubricants on a separate rack. Most often, some difficulties arise with storing small parts: screws, nuts and the like. You can use small glass jars with screw caps for this.

Screw the lid to the shelf below, sort all the small items into separate jars. This way you can save space and put things in order, and the search for the right screw, drill or nut will now be reduced to a minimum.

For these purposes, you can choose another option. You will need magnetic tape, small clear plastic containers with durable lids, and metal flat washers. Fix the magnetic tape vertically in the place you need.

Attach metal washers to the bottom of the containers. Sort all the small fasteners into ready-made containers and hang them on a magnetic strip.

For repairs you will also need inspection hole. And if it is not possible to equip it, then you can build two overpasses to lift the front or rear or side of the car. This will allow you to fully carry out all repair operations. Overpasses are made of timber and durable boards or metal if possible.

Well, in the end, good lighting is very important for the garage. It can be general and as an addition to portable and local lamps. And make sure that there is more than one outlet in the garage. If you are repairing the car yourself, then you need to think about ventilation of the room.

Video: 29 DIY projects for the garage

Order in the garage means convenient open storage of all frequently used tools and compact storage of various small items “in reserve”.

Often the garage and home workshop are combined, so all tools and consumables must have convenient system storage

As soon as the storage system becomes not very convenient for regular maintenance, the garage again turns into a spontaneous warehouse.

It is better to use open shelves to store tools in the garage. It will be very convenient if these shelves are removable.

In the garage of the workshop it is necessary to place not only the usual set of tools for a car enthusiast and a home craftsman, but, sometimes, also garden tools and camping equipment.

Make the most of the entire height of the room. In plastic boxes just under the ceiling and on the floor you can put those things that you use from time to time.

A tool storage system in a garage uses the entire wall area as a stand. Separate sections-shelves for storing tools and consumables.

Wooden guides are used here, but it is better to use metal pipes. If over time the guide we see in the photo crumbles, a box with a heavy tool could fall right on your foot.

You can make such an organizer for storing consumables yourself from sheets of plywood, which are connected with hinges in the form of a book.

A lockable stand-box for home craftsman's tools will allow him to easily maintain the necessary order in the garage.

Metal mesh is convenient for storing paint cans, fertilizer bags, etc.

Metal guides and metal shelves not only ensure safe tool storage, but are also easy to clean.

It is inconvenient to keep a power tool in a company suitcase; it is much more convenient to make such an open stand for storage.

The owner has a lot of necessary little things in his garage, and each of them has its own storage method.

Most tool storage methods are simple, but still more effective.

Very convenient design for storing consumables! The box with self-tapping screws that you use is secured to a separate panel, and upon completion of work, it is pushed into a common organizer.

Each owner has his own scope of activity and a different number of tools. But a convenient organization of work always makes you want to do something more. Take the time to tidy up your garage.

Sliding panels like extra bed for storing tools. Make sure that they will work reliably without getting stuck in the grooves, otherwise this storage method will not be practical.

Simple and convenient. Store your instrument wisely! If you don’t have a garage, and you store all your tools in a small box on the balcony, then even there you can organize a small work cabinet.

Let's continue for the happy owners of the garage. Before us convenient way storage of clamps.

Some storage ideas can be found in stores that sell tools.

But our garage contains more than just tools. We also have pipes, planks, and the necessary pieces of plywood and plastic.

It’s not at all difficult to assemble such a ceiling structure from pipes in your own garage.

Large sheets of plywood and drywall are best stored this way - in a vertical position.

For scraps of plywood, plastic, etc. You can make a wall rack like this.

Even a dozen boards can create a mess in your garage. Let's do it simple design for storage.

Another convenient way to store long pipes and all kinds of strips in the garage.

A small workbench can also serve as a storage place for boards and pieces of plywood.

You don't have to clean out your garage in one day. All this can be done gradually, step by step.